Most thread tangles start before the first stitch. A length that’s too long, strands that weren’t separated properly, or a thread that’s been twisting since the first pull: fix those three and embroidery suddenly feels a lot calmer.
Here’s how to cut, separate and thread six-strand floss, how to start and finish without bulky knots, and what to do when the thread misbehaves anyway.
What you’ll need
- Six-strand cotton embroidery floss
- Embroidery (crewel) needles, sizes 5 to 9
- Small sharp scissors
- Optional: a needle threader, and a floss bobbin or card for leftover lengths
How six-strand floss works
A skein of embroidery floss is six thin cotton threads loosely twisted together. You almost never stitch with all six at once. Instead you pull out the number of strands you need and recombine them. That’s how one skein can give you a fine line, a medium outline or a bold fill.
- 1 strand: very fine details, tiny lettering, delicate shading
- 2 strands: clean outlines and most lettering
- 3 strands: a bolder line, stems, general stitching
- 4 to 6 strands: chunky lines, French knots with more presence, bold satin stitch
Patterns usually say how many strands to use. If they don’t, two or three is a safe start.
Step 1: Cut a sensible length
Pull the floss from the end with the number tag on it (on many brands the loose end comes out cleanly from one side; if it bunches, try the other). Cut about 18 inches (45 cm), roughly from your fingertips to your elbow.
It’s tempting to cut a long piece so you rethread less often. It backfires: long thread tangles more, and the part near the needle gets worn and fuzzy from passing through the fabric over and over.
Step 2: Separate the strands
- Hold the cut length near one end, with about an inch sticking up above your fingers.
- Fan the top slightly so you can see the individual strands.
- Pinch one strand and pull it straight up, slowly. The rest of the bundle will bunch up below your fingers. That’s normal; keep pulling and it slides free.
- Smooth the bunched floss back out, and pull the next strand the same way.
- Lay the strands you need side by side, ends level.
Pulling strands out one at a time and putting them back together, rather than splitting the bundle in half, lets them lie flat and parallel. Your stitches look smoother and fuller as a result.

Step 3: Thread the needle
Choose a needle with an eye big enough for the number of strands. With crewel needles, smaller numbers are bigger needles: a size 5 suits 4 to 6 strands, a size 7 or 8 suits 2 to 3, and a 9 or 10 suits a single strand.
Three ways to get the floss through the eye:
- The fold: fold the end of the floss tightly over the needle shaft, pinch the fold flat, slide the needle out and push the flattened fold through the eye.
- Trim fresh: cut the end at a sharp angle so it isn’t frayed, and lightly moisten it.
- A needle threader: push the wire loop through the eye, drop the floss into it and pull back.
Leave a tail of 3 to 4 inches. Don’t knot the two ends together, unless you’re using the loop start below.
Step 4: Start without a knot
Knots are fine for a lot of projects, but they can make lumps under the fabric, show through light cloth and occasionally pull through. Two cleaner ways to start:
The waste knot
Knot the end and go down from the front about 2 inches away from where you’ll start, in the direction you’ll be stitching. Stitch toward the knot. Your stitches cover and secure the thread on the back. When you reach the knot, snip it off on the front. Nothing to hide.
The loop start (for an even number of strands)
For 2 strands, take a single strand twice as long as usual, fold it in half and thread both cut ends through the needle so the fold makes a loop at the other end. Come up from the back, make your first tiny stitch, and on the back pass the needle through the loop before pulling snug. It’s secure and completely flat.
Step 5: Finish the thread
When you have about 4 inches left, take the needle to the back. Slide it under three or four stitches nearby, ideally ones of a similar color, and pull through. For extra security, go back the other way under one or two stitches. Trim close.
Avoid carrying a thread across the back for more than about an inch to reach another area. Long carries can show through light fabric and catch on things. Finish and restart instead.
Troubleshooting
The thread keeps twisting into knots
Every stitch adds a little twist. Every few stitches, let the needle dangle with the hoop held up so the thread spins back. A shorter length helps too.
The strands come out of the needle different lengths
That’s from pulling the floss through the fabric unevenly. Re-level the ends at the eye from time to time. The loop start avoids it entirely.
Some strands lie loose and loopy in a stitch
The strands weren’t separated and recombined, or they’ve twisted. Separate them again, or run your needle under the stitch to smooth the strands before pulling tight.
The floss is fuzzy and dull
The length is worn out. Finish off and start a fresh length; it’s quicker than fighting it.
Keeping leftover floss tidy
Wind each color onto a plastic or card bobbin and write the color number on it. Leftovers are perfect for small hoops, flower centers and lettering, and they’re much easier to use when you know which shade they are.
Next, put the threaded needle to work with the beginner’s guide. If you’re still choosing thread colors, see choosing a thread palette.
FAQ
Should I use beeswax or thread conditioner?
It’s optional. Conditioner can help with tangle-prone thread such as metallics, but most people stitch with cotton floss untreated.
Can I mix different colors in one needle?
Yes. Threading one strand each of two close shades is a simple way to get a blended, slightly variegated look.
Which needle size do I need for floss?
For 2 to 3 strands of floss, a crewel needle around size 7 or 8 is a good fit. Go bigger (lower number) for more strands.


