A finished hoop that looks tidy from the back as well as the front feels like a proper gift. And it isn’t hard: trim, gather or glue, add a felt circle, and the messy back of your stitching disappears.
Below are the two main ways to finish an embroidery hoop for display, plus how to clean it up first and how to hang it.
What you’ll need
- Your finished embroidery and its hoop (a wooden hoop with a screw is easiest to finish)
- Fabric scissors
- Strong thread for gathering: sewing thread doubled, or two strands of floss
- A piece of felt slightly larger than the hoop
- Optional for the glued method: fabric glue or a low-temperature hot glue gun
- Optional: a circle of thin card or foam board to stiffen the back
- Optional: ribbon or twine for hanging
Before you start: clean and press
Remove any visible transfer lines first. Water-soluble pen needs a proper rinse in cool water rather than a quick dab, or it can come back. Let the piece dry flat on a towel.
To press, lay the embroidery face down on a fluffy towel and iron from the back. The towel lets the stitches sink in instead of being flattened. Use a temperature that suits the fabric.
Re-hoop for display
Put the fabric back in the hoop, centered and drum-tight. Check that the weave runs straight and that the screw sits at the top, where you’ll hang it. This is the time to fiddle; once the back is closed, adjusting is a pain.
Some people swap in a fresh hoop for display if the one they stitched with has marks or a bent ring.
Method 1: Running stitch and gather (no glue)
This is the traditional finish and it’s easy to undo later if you want to re-frame the piece.
- Trim the excess fabric to a circle about 1 to 1.5 inches (3 to 4 cm) beyond the hoop all round.
- Thread a needle with strong thread, knot the end, and sew a running stitch around the edge of the trimmed circle, about 1/2 inch (1 cm) from the edge.
- Pull the thread so the fabric gathers in over the back of the inner ring, like closing a drawstring bag. Keep the gathers even.
- Knot the thread securely and trim.

Method 2: Glued edge
Quicker and flatter, and the best option if the back will be seen up close. It’s harder to undo, so make sure you’re happy with the hooping first.
- Trim the excess fabric to about 3/4 inch (2 cm) beyond the hoop.
- Run a thin line of fabric glue (or low-temperature hot glue) along the inside edge of the inner ring, a short section at a time.
- Fold the fabric edge over onto the glue and press with your finger or a craft stick. Keep the folds small and even.
- Let the glue set before adding the backing.
Hot glue is quick but gets very hot and sets fast. Fabric glue gives you more time to adjust. Either way, keep glue off the front of the fabric.
Add a felt back
Felt hides the gathers or glued edge and gives the hoop a finished look.
- Glued felt: trace the inner ring onto felt, cut just inside the line so it fits snugly within the back of the hoop, and glue it over the gathered or glued fabric.
- Stitched felt: cut the felt slightly larger and whip-stitch or blanket-stitch it to the gathered fabric all round. No glue needed.
For a firmer back, place a circle of thin card or foam board behind the stitching before adding the felt. It keeps the fabric flat and stops it sagging over time.
A small label on the felt (your name, the date, a note for the person receiving it) is a nice touch for gifts.
Hanging the hoop
The screw at the top doubles as a hanger. Tie a loop of ribbon or twine through it, or hang it straight on a small nail. For a gallery wall, a small adhesive hook works for light hoops.
Keep finished embroidery out of strong direct sun. Cotton floss colors are fairly durable, but strong light can fade them over the years.
Troubleshooting
The fabric loosened after finishing
The fabric wasn’t tight enough when you closed the back, or the screw wasn’t fully tightened. If you gathered, you can usually open it, re-tighten and gather again. A card circle in the back helps keep it taut.
Glue soaked through to the front
Too much glue, or a very thin fabric. Use less glue, keep it on the inner ring rather than the fabric, and try fabric glue instead of hot glue on thin cloth.
The felt is visible from the front
It’s cut too big. Trim it so it sits inside the inner ring.
Transfer lines reappeared after framing
Water-soluble pen wasn’t fully rinsed out. Unfortunately the piece needs to come out and be rinsed properly. That’s why cleaning comes first.
Gift ideas once you know this finish
Small finished hoops make easy gifts and ornaments. If you’re stitching with a deadline in mind, last-minute embroidered gifts has a realistic time plan, and the hoop art and gifts hub has plenty of design ideas.
FAQ
Can I frame embroidery without a hoop?
Yes. Lace the fabric around a piece of acid-free board and put it in a picture frame. That’s a good choice for larger pieces.
Can I wash embroidery once it’s finished in a hoop?
Not easily. Wash or rinse before you finish the back.
How do I make a hoop ornament?
Use the same method with a small 3- or 4-inch hoop, then tie a ribbon loop through the screw.


