Close Menu
  • Start Here
  • Clothes
  • Florals
  • Gifts & Hoops
  • Sashiko & Mending
  • Beads
  • Tools
  • About
    • About StitchCraft Studio
    • Meet Lily
    • Contact
    • Privacy Policy
Facebook X (Twitter) Instagram
StitchCraft Studio
  • Start Here
  • Clothes
  • Florals
  • Gifts & Hoops
  • Sashiko & Mending
  • Beads
  • Tools
  • About
    • About StitchCraft Studio
    • Meet Lily
    • Contact
    • Privacy Policy
StitchCraft Studio
Home»Embroidery Tools»Floss & Hoop Calculator

Floss & Hoop Calculator

Use this calculator when you’re planning a new piece and want to know what to buy. Enter the size of your design, how many strands you’ll stitch with, how many colors it uses and roughly how much of it is filled in. The results update as you type.

Units
How much of the design is stitched?

How the calculator works

Hoop size

The hoop should fit the whole design with about an inch of fabric to spare on each side, so the calculator adds 2 inches (5 cm) to the longest side of your design and rounds up to the next common hoop size. For a rectangular design it also checks that the corners fit inside a round hoop. This matches the advice in setting up an embroidery hoop: a design about 4 inches across sits comfortably in a 6-inch hoop.

If the design needs more than a 14-inch hoop, the calculator suggests a frame or moving the hoop as you go instead.

Fabric size

Cut fabric about 4 inches (10 cm) larger than the hoop, so there are 2 inches beyond the hoop on every side. That gives you something to hold and pull taut, and enough to gather or glue at the back when you finish the hoop.

Needle

The needle suggestion follows the strand count: a size 9 or 10 crewel needle for a single strand, size 7 or 8 for two or three strands, and size 5 for four to six. With crewel needles, smaller numbers are bigger needles.

How much floss

A standard skein of six-strand cotton floss holds about 8 meters (8.7 yards), which is roughly 52 yards once you count each of the six strands separately. The calculator estimates how much single strand your design will use from its area and how much of it is filled:

  • Mostly lines and outlines: back stitch, stem stitch and similar line work. Thread use goes up with the number of strands you stitch with.
  • Lines with some filled shapes: line work plus some satin-stitched petals, leaves or lettering.
  • Mostly filled: satin stitch or long and short stitch over most of the design. Filled areas use far more floss, and the amount barely changes with strand count, because fewer strands simply means more stitches.

It then adds a quarter for starting and finishing tails and shows a range rather than one number, because stitch length, density and how you carry thread across the back all change the real amount. Since you can’t buy part of a skein, it suggests at least one skein of each color.

Tips for buying floss

  • If one color fills a large area, buy a spare skein of it. Dye lots can vary slightly, and it’s annoying to run out three petals from the end.
  • For small, mostly outline designs, one skein of each color is plenty and you’ll have leftovers for the next project.
  • If you’re choosing colors from scratch, choosing a thread palette explains how to pick shades that work together.

Want the other tool too? The Pattern Transfer Method Picker helps you choose how to get the design onto your fabric.

StitchCraft Studio

Embroidery ideas, stitch guides and easy patterns for clothes, hoops and gifts, by Lily Hartwell.

[email protected]

Follow on Pinterest

Embroidery hubs

  • Beginner Embroidery & Stitches
  • Embroidery on Clothes
  • Floral & Modern Designs
  • Hoop Art & Handmade Gifts
  • Sashiko & Visible Mending
  • Bead Embroidery

Start here

  • Beginner's guide to your first hoop
  • Transferring a pattern
  • Beginner supply checklist
  • Fixing puckered embroidery
  • Embroidery tools

About

  • About
  • Meet Lily
  • Contact
  • Privacy Policy
  • Affiliate Disclosure
  • Disclaimer
  • Terms

© 2026 StitchCraft Studio. All rights reserved.

Type above and press Enter to search. Press Esc to cancel.